jonathan2008
new member
Joined: 24/01/03
Posts: 11
Loc: Norfolk
|
Neumann too hot for AKAI?
#983503 - 21/04/12 02:27 PM
|
|
|
|
Ever the sucker for a silly name, I bought the AKAI EIEIO - the Pro version - and tried it
out on a friend who came around with acoustic guitar and some songs. I put a Rode NT4
(stereo mic) into two of the inputs and my trusty Neumann TLM103 into another. The Rode
was fine but the Neumann gave a whine, clearly audible in any silences, at around 2.5kHz.
It no longer whines but now gives a hum like a bad earth.
I have swapped
inputs, cables and cleaned contacts to no avail. The Neumann is fine going into my desk,
into a Zoom H4 and into an old Roland 1680. I've tried to replicate the hum with the Rode
and with an SE2200a but they both work fine with the AKAI. A technician friend thinks the
Neumann signal is too hot for the EIE Pro. Is he right? Is there anything I can do to fix
this?
--------------------
Jonathan
|
Jeraldo
Joined: 10/09/05
Posts: 2132
|
Re: Neumann too hot for AKAI?
[Re: jonathan2008]
#983518 - 21/04/12 05:40 PM
|
|
|
|
Try measuring the Akai's phantom power voltage with the 3 ( Rode X2) mic's connected, and
making sure the Rode is using phantom power from the Akai. Perhaps you could remove the
battery from the Rode mic if one is installed, just to reduce variables.
|
jonathan2008
new member
Joined: 24/01/03
Posts: 11
Loc: Norfolk
|
Re: Neumann too hot for AKAI?
[Re: Jeraldo]
#983628 - 22/04/12 01:50 PM
|
|
|
|
Thanks. The phantom power measures 51.4v at the unit and 51.v3 at the mic (inputs
1&2) and 50.4v at both the unit and the mic (inputs 3&4). Plugging in the Rode had
no effect on my measurements. I've previously been using the TLM103 with an
Allen&Heath desk (48.6v at the unit) and a Roland VS1680 (45.1) at the unit. Might
the voltage from the AKAI be too high for the mic?
--------------------
Jonathan
|
Jeraldo
Joined: 10/09/05
Posts: 2132
|
Re: Neumann too hot for AKAI?
[Re: jonathan2008]
#983802 - 23/04/12 02:36 PM
|
|
|
|
Assuming you made the measurements with mic's plugged in, the voltage is within spec.
The symptoms don't seem to be consistent with a mic that is too hot for an
input.
Perhaps someone will be by with a good answer. Until then, I think it's
a matter of careful elimination of variables to determine the cause. But I don't think the
output level of the mic is the problem.
|
jonathan2008
new member
Joined: 24/01/03
Posts: 11
Loc: Norfolk
|
Re: Neumann too hot for AKAI?
[Re: Jeraldo]
#983812 - 23/04/12 03:37 PM
|
|
|
|
Thank you, Jeraldo.
(I should also have mentioned the current - 6.86mA at the
mic.) But is it possible to measure the voltage with the mic plugged in? I unplugged the
mic in order to get to the female XLR plug with my multimeter.
As you say, it
doesn't appear to be a voltage problem and the mic checks out fine elsewhere. I shall ask
Neumann too, and post their response. Meanwhile I remain open suggestions from the room.
--------------------
Jonathan
|
Hugh Robjohns
SOS Technical Editor
Joined: 25/07/03
Posts: 18390
Loc: Worcestershire
|
Re: Neumann too hot for AKAI?
[Re: jonathan2008]
#983814 - 23/04/12 03:46 PM
|
|
|
Quote jonathan2008:
The Rode was
fine but the Neumann gave a whine, clearly audible in any silences, at around 2.5kHz. It
no longer whines but now gives a hum like a bad earth.
Whines and whistles are usually caused by
some form on interference getting into the mic through bad cables etc, or by noise from a
DC-DC converter getting into the power rails.
Quote:
A technician friend thinks the Neumann signal is
too hot for the EIE Pro.
Not
likely -- that would cause distortion, not whistles. The TLM103 is more sensitive than the
Rode, but only by 5dB. It also takes almost half the phantom current, so I would have
expected the Rode to cause DC-DC problems rather than the Neumann!
hugh
--------------------
Technical Editor, Sound On Sound
|
Hugh Robjohns
SOS Technical Editor
Joined: 25/07/03
Posts: 18390
Loc: Worcestershire
|
Re: Neumann too hot for AKAI?
[Re: jonathan2008]
#983816 - 23/04/12 03:54 PM
|
|
|
Quote jonathan2008:
The phantom
power measures 51.4v at the unit and 51.v3 at the mic (inputs 1&2) and 50.4v at both the
unit and the mic (inputs 3&4).
This is slightly high but well within tolerances. There shouldn't be able voltage drop
across a short-ish cable -- if there is it suggests the cable has significant resitance
which isn't a good thing!
The phantom voltage at thge mic will be lower when a
load (mic) is connected because the current flow through the output resistors with
generate a voltage loss. It should be between about 32 and 38V for the Rode and Neumann,
respectively.
Quote:
Might the voltage from the AKAI be too high for the mic?
No, the phantom spec is 48 +/-4V -- meaning
44-52V is the tolerance range and your system is easily within that.
Your
current measurement (presumably shorting between pins 2/3 and 1) of 7mA indicates a
healthy supply too.
Hugh
--------------------
Technical Editor, Sound On Sound
|
jonathan2008
new member
Joined: 24/01/03
Posts: 11
Loc: Norfolk
|
Re: Neumann too hot for AKAI?
[Re: Hugh Robjohns]
#983974 - 24/04/12 01:17 PM
|
|
|
|
Thanks, Hugh.
It's reassuring to know that both items appear to be functioning
properly. But I'm left with two good pieces of kit that work fine with everything else
but not with each other.
The only thing I can add is that when I scratch the
mic grill with my fingernails I get a clean sound with the mixer etc, but a distorted
sound with the AKAI EIE.
--------------------
Jonathan
|
jonathan2008
new member
Joined: 24/01/03
Posts: 11
Loc: Norfolk
|
Re: Neumann too hot for AKAI?
[Re: jonathan2008]
#986787 - 10/05/12 07:53 PM
|
|
|
|
I thought I'd better finish the story. After conversations with Neumann, AKAI and Digital
Village (who supplied the EIEPro), much scratching of heads, testing of voltages and an
XLR cable upgrade to one with Neutrik plugs I still couldn't use the mic with the
interface.
But yesterday Digital Village replaced the unit and today microphone
and interface are working together very happily. So it was probably a fault with the AKAI
all along. I'd still recommend the EIEPro though and am very pleased to report a happy
ending.
--------------------
Jonathan
|
Jeraldo
Joined: 10/09/05
Posts: 2132
|
Re: Neumann too hot for AKAI?
[Re: jonathan2008]
#986980 - 12/05/12 12:25 AM
|
|
|
|
Thanks very much for posting what happened! I had wondered about this one. Glad you have
it sorted. It would be interesting to know exactly what the fault was, but I doubt there's
a chance of that.
|
Previous
Topics
Next
Threaded
Edit
Reply
Quote
