Jerry Boys & Livingston Studios : September 2007
In this article:
Gnarls Barkley & The Atlanta Sound Ben Allen
Mixing R&B
Scissor Sisters: Recording Ta-Dah Babydaddy • Dan Grech-Marguerat The Scissor Sisters' first album, recorded in a Manhattan apartment, sold 3.5 million copies worldwide. The follow-up sees them expanding their horizons, while keeping their DIY ethos very much intact. Artist/Producer
Writing & Producing With Robbie Williams Despite his best efforts, Stephen Duffy's solo work never quite made him a superstar — but it did get him one of the best co-writing gigs around. Producing Kasabian & Arctic Monkeys
Uwe Schmidt: Recording Yellow Fever! Yellow Magic Orchestra goes Latino Yellow Magic Orchestra helped pioneer the use of electronic instruments and sampling. Now Uwe Schmidt, aka Señor Coconut, has used the same techniques to render their greatest hits as Latin dances, with contributions from all three original YMO members. Recording Morph The Cat
Folk Music For The 21st Century The idea of bringing folk music up to date is not a new one, but few people have taken it quite as far as Jim Moray. His material may be traditional, but his approach to music technology is as modern as it gets. Recording David Gilmour's On An Island Andy Jackson David Gilmour's chart-topping solo album was recorded on his own Astoria houseboat, a floating slice of studio heaven. Engineer Andy Jackson describes the making of the album. Producing Eminem & Fiona Apple Mike Elizondo
Roger Nichols: Across The Board The Current State Of Affairs What can we, as engineers or musicians, do to prevent our recorded legacy being lost? Record Producer
Richard Aitken of Nimrod Productions
Writing & Producing in LA The success of Avril Lavigne's debut album Let Go catapulted The Matrix to the front rank of songwriters and producers. Since then, they've moved in ever wider musical circles, culminating in their work with nu-metal pioneers Korn. Producing Hip-Hop Miami is now a hip-hop centre to rival New York and LA, and Cool & Dre are two of its most active beatmakers, songwriters and producers. Craig Bauer Craig Bauer has been part of Kanye West's career from the beginning, and as a mix engineer on the smash hit Late Registration album, he had to marry West's artistic perfectionism with his own technical standards. Producing The Darkness's One Way Ticket To Hell... And Back Roy Thomas Baker
John Fryer
Harry Gregson-Williams
September 2010
Click image for September 2010
Other recent issues: | Jerry Boys & Livingston StudiosWorld RecordsPeople + Opinion : Artists / Engineers / Producers / Programmers In an age dominated by software and samples, Jerry Boys has found the perfect niche for his old-school engineering skills: as the first-call specialist in recording world music.  Starting out in the music business in 1965 as an engineer at Abbey Road, Jerry went on to work at London’s Olympic and Sound Techniques studios, as well as Sawmills in Cornwall. But since his return to London in early 1982 he’s been based in the same place: Livingston Studios in Wood Green. Photos: Richard Ecclestone It’s hard to find engineers of Jerry Boys’ pedigree these days. As the diminishing number of large studios pushes many of the most experienced into retirement (or worse, into office jobs), there are only a handful of people left in the studio community who have CVs as colourful as his. Starting out in the music business in 1965 as an engineer at Abbey Road, Jerry went on to work at London’s Olympic and Sound Techniques studios, as well as Sawmills in Cornwall. But since his return to London in early 1982 he’s been based in the same place: Livingston Studios in Wood Green. A substantial number of folk and rock projects with the likes of Richard Thompson, Steeleye Span and REM followed this move, and Jerry became widely known and respected for his attitude towards recording, which, to this day, centres round a distinctly natural approach. “I like a group of people playing in the studio, as close to complete as possible. At one point in the late ’80s, when MIDI started to be a big thing, I actually retired, just to run the studio. This lasted for about a week until somebody rang me up with an interesting project. It was Everything But The Girl, and I said ‘Oh, all right then’, and we ended up making five records together. “But then Ben [Watt, from Everything But The Girl] suddenly went from being a man interested in studio stuff, to a programmer. I don’t know why, but someone introduced him to a programmer and they did a couple of tracks on what was supposed to be a completely acoustic record. The brief to me was ‘We’re all going to sit out in the studio and play, you’re not allowed to EQ anything, you’ve got to do it all with microphones, and it’s gotta be all organic’, which was quite good fun; I liked that sort of challenge, and it taught me a few things. But in the middle of it, they went off and did two or three tracks, one of which was ‘Missing’, then they came back and did a few bits to them to make them fit into the rest of the record. “Ben had realised that there was this whole creative world out there, and he built himself a pretty nice home studio off the back of the money he made. At that stage, I’d decided that if people weren’t going to play, I wasn’t going to make their records. And it’s worked out fine!” The Start Of A Revolution  Jerry Boys’ policy is to record to analogue tape on his Otari MTR90, then transfer the multitrack to Pro Tools. It was Jerry’s natural approach that attracted acclaimed producer Joe Boyd. The pair did a few projects together, which led to a meeting with World Circuit Records producer and founder Nick Gold. “Nick asked Joe ‘Who do you use as an engineer? I can’t find anyone I can get on with.’ And Joe said ‘Well, try Jerry Boys.’ So myself and Nick went off and did a record with Malian singer Oumou Sangare, and we just hit it off; we got on really well.” Soon after this, Jerry was asked to make the trip to EGREM studios in Havana. “Nick said ‘By the way, I’m going out to Cuba to do a record with Ry Cooder, would you be interested in engineering it?’ I said ‘Of course I will.’ So we went and did this trip, and recorded Afro Cuban All Stars, the first Rueben Gonzalez album and the Buena Vista Social Club album, all in two weeks. Of which two days was spent fixing the tape machine!” A few years later, Nick and World Circuit Records bought Livingston Studios, and since then, studio and engineer have specialised in recording music from Africa, Asia and Latin America. In that context, Jerry Boys began to accept that there was a place for digital recording in his work. “You can’t deny that there are lots of things that you can do in Pro Tools that you can’t do easily on analogue. And once you’ve been made aware of all these things, and started to use them, it’s very hard not being able to do them. Also, if you’re travelling, you can’t really cart an Otari MTR90 around with you!” He’s not ready to chuck out the MTR90 altogether, though. “We did some tracking on to Pro Tools HD running at 24bit/96kHz, in a studio in Senegal. We were fairly happy with the results; we weren’t aware of anything going terribly wrong, so we added a few extra guitar parts, and some drums and percussion. “Then we started to do the mixing back in the studio at Livingston, and Nick was worried about the hi-hat, which is a big feature in every song, since there’s not much in the way of regular drums; it just sounded a bit too ‘spiky’. So we listened to the hi-hat that we recorded to tape using the analogue gear here, and it was much softer. I suggested that we transfer all the percussive stuff on to analogue and then back into Pro Tools, to see what happens. “So we did exactly this, with the level at +7dB instead of +4dB, because I really wanted to steam the level and get some tape compression. Once the transfer had taken place, we played it back and switched between tape and Pro Tools. Sure enough, it had done exactly what we’d expected it to do; the tape had blurred the edges and made it nicely compressed. We were really pleased with ourselves. Then we wondered what was going to happen when we put it back into Pro Tools, so we did the reverse thing and laid it back onto hard disk. And bugger me, it had regressed back to being ‘digital’. Not completely, but it had gone back maybe 25 percent.  Livingston’s Studio Two is used mainly for mixing, a role that is reflected in its selection of rackmount gear. Top to bottom, from far left: Dbx 283X de-esser (x2), Smart Research C1 dual compressor, Neve 2254 compressor (x2, with custom-wired stereo link), Dbx 160XT compressor (x2), Urei LA4 compressor (x2) and silver-faced Urei 1176 compressor; (on top of second rack) Teletronix LA2A compressor, GML 8200 EQ, Lexicon 300 effects, Neve 2262 compressor (x2); (in rack) GML mic preamps, Universal Audio 2-610 dual-channel tube preamp, Boss TU50 tuner, Drawmer LX20 compressor, Dbx 160X compressor, Gates Sta-Level compressor, and Dbx 1066 and 266XL compressor/gates. Above the third rack is a black-faced Urei 1176LN, plus some of SSL’s modern XLogic gear; the rack itself contains Roland SDE3000A digital delay, Lexicon Alex, Alesis Quadraverb, Yamaha SPX900 and REV5, Lexicon Model 200 reverbs and Eventide FL201 flanger. Column four contains another Roland SDE3000A, Lexicon PCM80 reverb, Zoom 1201 and Eventide H3000DSE effects, Pultec HLF3C filter and Drawmer DS201 gate. “I’ve always had this thing about digital, in that it has this really hard sound; it never seems to go together. Everything sounds good individually, but it doesn’t blend, whereas analogue blurs things a bit. And I don’t pummel the level on analogue normally, I try and keep it cleanish. I use Dolby [SR noise reduction] and I run at 15ips. “When recording to digital, I do see the point of using high sample rates. I know that my MTR90, when it was new, would only be 3dB down at 27kHz, and it still had stuff going on up into the 40s. When using a 48kHz sample rate, you get a brick-wall filter at 24kHz, and although we can’t hear a tone that high, you are aware of the harmonic information, which is what I call ‘air’. This is why I record at 96kHz. Now if you’re working on a sampled record, or a loud electric guitar record, then maybe it doesn’t matter. But for anything with any sort of top end in it — all the records I generally do — I think a higher sample rate is really important. “After the tests we did on the Senegal material, recording to digital really concerns me now, because it’s actually changing the sound. As a result, we’ve decided now that we’re going to record to analogue, then transfer to Pro Tools when we’ve gone as far as we can go. Needless to say, I’m afraid I’m still an analogue man.” A Club Record World music all too rarely achieves mainstream visibility in the UK, but that changed with the success of Buena Vista Social Club. It’s the best-selling album of world music ever, and has shifted almost eight million copies, a result that vindicated Jerry Boys’ ethos of “a group of people playing in the studio”. “The recording of Buena Vista Social Club itself took about eight days. It’s all live, apart from Ry’s electric stuff, which is overdubbed. Vocals, the lot, were done live in the studio. It was the only way, as the artists on the record aren’t the sort of people that are used to studio recording: half of them had probably never worn headphones before! “Before we did Buena Vista Social Club, we did Afro Cuban All Stars, which was recorded in much more normal sort of way — rhythm sections first, then overdubbed horns and voices and so on — and that’s really hard work. It was a great record, but it was absolutely knackering. We worked from 10.30 in the morning ‘til about 2.30 at night, every day for about six days.”  Studio One is typically used for tracking, and the gear rack is full of mic preamps and input processors. From top left: Neve 33415 modules (x8), API 3124 preamps (x2), transformerless GML preamps (x4), Universal Audio 2610 preamp, API 550 EQ (x2, in Lunchbox), Drawmer DS201 noise gate (x2), EAR 822Q EQ, Audio Design Recording F769XR Vocal Stresser and Pultec HLF3C filter; (right) Neve 33609C, BSS DPR402, Dbx 160XT (x2), Tube-Tech CL1B, Urei 1176 (x2) and Gates Sta-Level compressors, Dbx 263X de-esser (x2), BBE 422A enhancer and Urei LA3A compressor. But it wasn’t as simple as setting up kit and recording; Jerry and the team had to learn many of the intricacies of Latin music on the spot. “Cuban music isn’t so different in terms of instrumentation: a trumpet is a trumpet, and you don’t meet many unusual instruments. But the rhythm is very different. Although it might not seem so on the face of it, it’s all based around what’s called clave. I’m not very good at it myself, but clave goes in two and then three, or three and then two, or any combination of the two, and there are lots of them. And that’s how they hear music, they don’t hear it like we do. Often what we hear as a one-bar sequence repeated, is in fact a two-bar sequence repeated, because the clave goes across two bars. “So on the Cuban sessions, we did cuts, and we thought we’d done a great edit, and they’d go ‘No, no, you can’t do it like that, because you’ve ruined the clave.’ We had great arguments in the studio about this, and even the Cubans would argue amongst themselves abvout the clave sometimes. So that was the mystery. Once you understand where the clave is, all the funny timing and stabs they do on the horns make more sense. I didn’t know any of this when I went over to do the first Cuba sessions.” Trumpets Like Lasers It wasn’t just a different understanding of musical arrangement that Jerry encountered in Cuba. “They have learned how to play loud. On American records, you hear those laser-like trumpets and you think ‘How the fuck do they do that?’ You wonder what microphone they use and so on, but when I walked in the room on the first rehearsal in Cuba, and the trumpets all lit up, I thought ‘Fuck, there’s that sound!’ It’s all in the playing, it’s just the loudest thing ever! They just make this really hard, edgy sound. “When it comes to miking up trumpets, I tend to use one microphone in front of the three of them, back a while. But because EGREM is such a great room, I’d usually have a pair of ambient mics up all the time. The trouble with these is that it makes dropping in difficult. It depends on who you work with; some people will want one microphone on each trumpet separately. It doesn’t sound as good, but it does mean that you can drop in on trumpet parts. With one mic on all three, you get a much more integrated, very exciting sound, but it doesn’t have much to do with the engineer.” The Cuban musicians may have been unfamiliar with studio conventions, but they were orthodox compared with the late Ali Farka Touré, who Jerry worked with extensively over the years. “He had this strange guitar, I don’t know what it’s called, but it was Japanese, and it had a built-in speaker. I remember seeing them in the early ’70s; it looked a bit like a Gibson SG. You’d have to plug it into the right amp, a Roland JC120, but that’s all there was to it. I’d often go and twiddle the amplifier, because I always found that he either had it too loud or not loud enough. Also, he didn’t understand the implications of having the volume on the guitar right up, so you got a lot of noise. Before he arrived on a session, we used to tune the guitar for him using a tuner, so it was at the ‘correct’ pitch. But then he’d get it and make all kinds of crazy noises, and fuck knows what he did. But it worked for him.  Jerry Boys’ favourite mics are mostly familiar Neumann, AKG and RCA models, but there are a few oddballs lurking in Livingston, including the AKG D190, which has been uniquely customised, a Sony C38B and a Microtech Gefell UM70. “He was a great man, the end of a generation, you know. An untrained, unadulterated musician, and never much influenced by others.” Classic Choices Musicians such as Ali Farka Touré don’t give bad performances, but it’s still up to Jerry to capture them at their best. To do so, he employs a fairly robust selection of tools. “When setting up mics, I have favourites for different things, but I guess a [Neumann] U87 would be my first choice. If I only had one mic in the world, it would be that one. I use AKG 414s for various things, and Neumann KM84s and TLM170s quite a lot. I use them as ambient mics, but I also use them on trumpets, because they’re just a little less hard in the middle than an 87 is. After that, there are the specialist ones; I usually use an AKG D112 on the bass drum, a U47 FET on string bass. “Although I’ve got one, I’m not a big lover of U47 valves, but I quite like U49s. But with these, you’ve got to find the right one and the right thing to use it on. AKG C12s are quite nice sometimes; I use the odd dynamic, an SM57 or an MD421, for example, on toms, and then there are a few things that get used here at Livingston. We’ve got a Calrec 1050, which is not made any more, but they were really cheap, and really good on acoustic guitars or as overheads. I’m not saying there aren’t other great microphones in the world, but I like the ones I know. “I do try others occasionally, but they’re never as good as the real thing. I was in a studio in Senegal, and I tried an SE mic. I asked the local engineer what he used it for, and he said ‘electric guitars’, for which I would normally use a U87, so I stuck it up and compared it. The 87 sounded better. The SE wasn’t unusable, but it sounded different. It didn’t sound shit, but I didn’t really think ‘I’ll remember this.’ I just thought it sounded like a cross between a 414 and an 87, but not as good as either of them. “You need a pair of ears when you make microphones. You may be able to make very clever technology, but that doesn’t always mean you’re good at making things sound nice. The Chinese and Japanese are normally OK at making things like effects processors, because that involves digital technology and computer skills, and gear that works can be made cheaply. On the other hand, the British were good at making products that sounded good, but they weren’t so good at the other parts.” But Jerry’s the first to admit that even his favourite manufacturers can slip up. “Neumann don’t make 84s any more, they make 184s, and they don’t sound anywhere near as good as an 84. I’ll use 184s occasionally — particularly on hi-hat if I want a tight sound — but I’d never use one by choice; only if I’d run out of 84s. Even Neumann don’t always make good microphones.” It may come as no surprise that Jerry uses a formidable set of outboard equipment at the other end of the mic cable. The gear at Livingston Studios has been accumulated over some time, and includes items from as far back as the ’50s, such as the Gates Sta-Level, a variable-mu compressor that has a reputation for working wonders on bass. Studio One’s racks reflect its main use as a venue for tracking and recording. Bespoke preamps and outboard processors sit alongside a ‘black knob’ SSL 4000E (see the ‘Unsung Heroes’ box) and, with behind-the-desk lines of sight to the main live room and all the annexed amp rooms, it’s an engineer’s dream. Studio Two is preferred for mixing, as its control room is smaller and cosier. Jerry spends a lot of time in this room, and he runs a tight ship: “I’m the only person allowed to put tea on the mixing desk. I can tell myself off then!”  Jerry’s most commercially successful recording, the Buena Vista Social Club album, was recorded at EGREM studios in Havana, Cuba. The picture above shows Ibrahim Ferrer (left) and Omara Portuondo (right) duetting on ‘Silencio’. As with the other Social Club artists, they performed together live, without headphones. Different versions of Jerry’s favourite mic, the Neumann U87, can be seen in use here. Words Of Wisdom After 40 years in the business, Jerry Boys is in a strong position to impart useful advice to budding engineers. He’s a believer in the traditional career path, along with old-fashioned persistence and patience. “I think that watching and listening are the main things that a developing engineer should concentrate on, and I still feel that, if you want to be a recording engineer, you need to get a job in a real studio and watch other people doing what they do. The only way to do that is to be a tea boy, then a tape-op, and I think you really need to be a tape-op for at least three years if you want to be any good. However, the future is in the computer, the Pro Tools world; and you can learn quite a lot of that stuff by going to college. “The real gist of it is that you just have to keep trying, although the majority of jobs involve a fair amount of luck. You might meet someone in the pub, or something fortunate will happen. Whatever your situation, you have to be prepared to give up a lot. You have to have no concept of regular hobbies. “I guarantee that if one of the Livingston engineers came in and said ‘I’ve been offered a job at Olympic, I’m leaving in a month,’ we’d get out the file of applicants, and start at the front, where all the most recent CVs are. Maybe you have 30 applications, so you phone them all up, and interview them. Obviously, applicants need something that says that they can do the job, but if you happen to turn up on the day with a letter and a CV, that’s the first one you’re going to look at.” Future Gems It’s Jerry’s positive attitude that has allowed him to retain at the top of the list of veteran engineers, and it doesn’t look as though he’s going to pack it up any time soon. The current project with World Circuit is an album with Orchestra Baobab, a Senegalese outfit whose Afro-Cuban style has been popular in the West African country since the ’70s, and outside of the World Circuit projects, Jerry has also been in the studio with Columbian temptress Shakira, working on tracks for the forthcoming film Madagascar II. Needless to say, Jerry is still very much in demand. 0  Unsung Heroes: Pete Martelli  Peer behind the racks or in the machine room at Livingston, and you’ll come across Pete Martelli, chief maintenance engineer. Pete’s been working at the Wood Green studio since 1980, at the time that Nick Kinsey, son of then-owner Ray Kinsey, began to transform a dilapidated chapel into what is now Livingston Studios. “Nick was a genius,” says Pete. “He managed to build a really professional-sounding studio for next to no money. That’s why there is fencing on the ceiling of Studio One’s live room, and the walls are covered in bathroom tiles! The room hasn’t changed since he made it, although we’ve had new flooring put in recently”. The mainstay of Studio One is a custom-made SSL 4000E. “The desk has been here for 20-odd years now, it was brand new when we got it. Jerry specified that channels 1-24 should be in the middle of the console, because those generally contain the tracks that you’re going to record on most. He always though that to have these in the centre of the stereo image was a good idea. Most SSLs you see will be numbered 1-48 in sequence across the console. “It’s also got Black Knob EQ, which Jerry and Nick also specified. When they decided that they were going to have an SSL, they got an E-series EQ module from SSL, and set up an oscillator and an audio level meter, and plotted the EQ curve. Then they decided that they’d like half a decibel at 3kHz, or whatever, and asked SSL whether they could modify the EQ to their parameters, and they did, and assigned it a black knob. In fact, SSL used that design on a lot of their subsequent models. Both Studio One and Two feature custom-made soffit-mounted main monitors, plus a selection of nearfields. “The soffits consist of a pair of JBL 2235, and a TAD driver, driven through Whyte crossovers. But we also have a selection of NS10s, Auratones and Genelec speakers.” But at Livingston, the humble NS10 isn’t just used for monitoring purposes. “There are NS10 drivers in the ceiling for talkback, and we use a couple as microphones, on kick drums and so on.” Travelling Light Successfully transporting a recording rig from London to Senegal or Cuba involves a crash course in global logistics. By now, Jerry and the World Circuit team are experts, as maintenance engineer Pete Martelli explains. “Modern recording gear travels well, but there are certain things to be cautious about. I try not to take old valve stuff; I take tried-and-tested modern things, and they all seem to make it to the other side in one piece. We’ve travelled with a hired Pro Tools rig a few times now, and we’ve had no problems. “I don’t take ribbon mics; I think they’re too fragile to be bumped around the world, and too expensive to replace! We’ve learned that if you send your equipment as air freight, it generally gets treated better than it does if you check it in as hold luggage. If you’ve ever looked out the window when they’re loading baggage, it’s horrendous. I’ve seen someone drop a guitar from the top of the baggage trolley. “But for our next trip to Senegal, we’re just going to take six microphones and one API 3124 mic amp. We’ll use their Pro Tools rig the way it is. I’ll just take one of our hard drives, which so far have never let us down. Maybe I’ll take two, I’ll talk to the boss!” 
Home |
Search |
News |
Current Issue |
Digital Editions |
Articles |
Forum |
Subscribe |
Shop |
Readers Ads
 Advertise | Information | Links | Privacy Policy | Support | Thursday 9th September 2010 Secrets Of The Mix Engineers: Humberto Gatica Inside Track: Michael Bublé ‘You’re Nobody Till Somebody Loves You’ In a rare interview, legendary engineer and producer Humberto Gatica explains how he and singer Michael Bublé breathed new life into big-band swing music — with stunning results. Midlake: Recording The Courage Of Others Tim Smith & Paul Alexander
Orchestrion Manoeuvres
David & Peter Brewis: Recording Field Music (Measure) Studio experimentation
Dave Fridmann: Producing Embryonic Following their unlikely breakthrough into the mainstream, Flaming Lips made a conscious return to the outer limits with their recent album Embryonic. Dave Fridmann manned the controls. Producing Arctic Monkeys
Wayne Bennett & Speech Debelle Recording Speech Therapy
Imogen Heap - Recording Ellipse Making An Album Solo
Secrets Of The Mix Engineers: Young Guru Inside Track: Jay Z's The Blueprint 3
Secrets Of The Mix Engineers: Fraser T Smith Inside Track: Tinchy Stryder
Bruce Swedien: Recording Michael Jackson Legendary engineer on Thriller
James Wiltshire: Producer & Remixer We cross-examine James Wiltshire of the Freemasons to uncover the secrets of their phenomenal success as a production and remix team. Secrets Of The Mix Engineers: Dot Da Genius Kid Cudi: ‘Day ’n Nite’
Secrets Of The Mix Engineers: John Fields & Paul David Hager Jonas Brothers
Producing Trance
Classic Tracks | Aerosmith ‘Walk This Way’ Producer: Jack Douglas • Engineer: Jay Messina
Secrets Of The Mix Engineers: Peter Mokran Track: Jai Ho! (You Are My Destiny)
Doves: Producing Kingdom Of Rust Dan Austin & Jez Williams
Secrets Of The Mix Engineers: Dylan ‘3D’ Dresdow Black Eyed Peas For their fifth album, The END, Black Eyed Peas main man will.i.am took the band — and their long-serving mixer Dylan Dresdow — in a new direction, with stunning success. Simple Minds: Recording Graffiti Soul Jez Coad & Simple Minds Thirty years after their debut, Simple Minds returned to their roots as a live band and relit the old fires to record their most impressive album in years. |
|
| ||
Email: Contact SOS Telephone: +44 (0)1954 789888 Fax: +44 (0)1954 789895 Registered Office: Media House, Trafalgar Way, Bar Hill, Cambridge, CB23 8SQ, United Kingdom. Sound On Sound Ltd is registered in England and Wales. Company number: 3015516 VAT number: GB 638 5307 26   Current MagazineeSub EditionBuy PDF articlesMagazine FeedbackDigital EditionsUK editionUSA digital editionPodcastsCompetitionsSubscribeSubscribe NoweSub FAQsHomeNewsSearchNew SearchForum SearchSearch TipsArticlesReviewsTechniqueSound AdvicePeopleGlossarySoundBankHelp + SupportForumToday's Hot TopicsForum Channel ListForum SearchMy Forum HomeMy Forum SettingsMy Private MessagesForum Rules & EtiquetteSOS TVWatch exhibition videos, tutorials,
| ||
Printer-friendly version
