You are here

Build project - resonator guitar from recycled bits

Page 8 of 21

Re: Build project - resonator guitar from recycled bits

PostPosted: Fri Feb 02, 2018 8:36 pm
by Martin Walker
My goodness - look at the glossy gleam on that body!! :o


Martin

Re: Build project - resonator guitar from recycled bits

PostPosted: Fri Feb 02, 2018 9:40 pm
by adrian_k
Thanks for the encouragement one and all :)

As to the finish on the sides - not what I would choose, I’ll have to do something about that high gloss. :sick:

Re: Build project - resonator guitar from recycled bits

PostPosted: Fri Feb 02, 2018 11:03 pm
by Wonks
Martin Walker wrote:My goodness - look at the glossy gleam on that body!! :o
That's just sweat from all the clamping.

Re: Build project - resonator guitar from recycled bits

PostPosted: Sun Feb 04, 2018 3:30 pm
by adrian_k
More likely from carving all those braces for the top ....

Which reminds me, Col gave me a nice little present this visit - my very own monogrammed thumb plane. :D
Image

Re: Build project - resonator guitar from recycled bits

PostPosted: Sun Feb 04, 2018 3:34 pm
by blinddrew
Worth it all just for that! :)

Re: Build project - resonator guitar from recycled bits

PostPosted: Sun Feb 04, 2018 3:42 pm
by adrian_k
Yes my evil plan is working. Next month a full set of chisels mwahahahahaha!

Re: Build project - resonator guitar from recycled bits

PostPosted: Sun Feb 04, 2018 5:27 pm
by Martin Walker
adrian_k wrote:More likely from carving all those braces for the top ....

Which reminds me, Col gave me a nice little present this visit - my very own monogrammed thumb plane. :D
Image

But how often do you need to plane your thumb adrian? :beamup:


Martin

Re: Build project - resonator guitar from recycled bits

PostPosted: Sun Feb 04, 2018 5:58 pm
by Wonks
He has very hairy hands. ;)

Re: Build project - resonator guitar from recycled bits

PostPosted: Sun Feb 04, 2018 8:04 pm
by adrian_k
Martin Walker wrote:But how often do you need to plane your thumb adrian? :beamup:


Martin

I do it all the time.... not on purpose obviously :headbang:

Re: Build project - resonator guitar from recycled bits

PostPosted: Mon Feb 05, 2018 10:33 am
by garrettendi
Looks stunning so far!

Re: Build project - resonator guitar from recycled bits

PostPosted: Wed Feb 14, 2018 3:17 pm
by Guest
What tuning heads you going with Adrian?

Re: Build project - resonator guitar from recycled bits

PostPosted: Wed Mar 07, 2018 8:03 am
by adrian_k
ReadySaltedChris wrote:What tuning heads you going with Adrian?

Oops just seen this...

Not sure... I think I might just go with something plain and not too modern. It’s not going to be a slotted head so maybe some open gear ones with white buttons, I’ll have a look around.

Col used to like either Grovers or Sperzels but says the quality has gone down over the years and he now prefers Gotohs.

Any suggestions?

Re: Build project - resonator guitar from recycled bits

PostPosted: Wed Mar 07, 2018 1:56 pm
by blinddrew
I've got Grovers on my Cole Clark and Schallers on my Hofner, both of which seem to be better than the defaults on my other guitars, but I've never tried the Gotohs or the Sperzels.

Re: Build project - resonator guitar from recycled bits

PostPosted: Fri Mar 09, 2018 1:59 pm
by adrian_k
blinddrew wrote:I've got Grovers on my Cole Clark and Schallers on my Hofner, both of which seem to be better than the defaults on my other guitars, but I've never tried the Gotohs or the Sperzels.

Hmm.. tricky. And then do I go vintage or contemporary style? Decisions decisions...

Re: Build project - resonator guitar from recycled bits

PostPosted: Fri Mar 09, 2018 2:19 pm
by adrian_k
Right, on we go.

First job this month was to route off the surplus from the new top, and sand the sides to make sure sides and edge of top are absolutely in line.

Image

That tape is there because I although carefully took the router round 'with' the grain as instructed I still managed to split the top about 4mm from the edge. The broken bit is still glued to the lining so it's not flapping about, and the binding might take care of it, but I still ran some superglue in and taped it while it dried. Fingers crossed.

The right hand pic shows how the Tanglewood neck was attached - three dowels. The block I let in was where a couple of rods went from the neck into a plate underneath the fingerboard.